by clicking the arrows at the side of the page, or by using the toolbar.
by clicking anywhere on the page.
by dragging the page around when zoomed in.
by clicking anywhere on the page when zoomed in.
web sites or send emails by clicking on hyperlinks.
Email this page to a friend
Search this issue
Index - jump to page or section
Archive - view past issues
button in toolbar for more information.
Metal Casting Technologies : Dec 2009
METAL Casting Technologies December 2009 33 he Boeing 787 airliner goes into commercial service next year and passengers will be transported on wings and fuselages made of advanced composite plastics. This raises a logical question: if modern plastics are sturdy enough for 600 mile- per-hour airplanes, why are car engines still made by pouring molten metal into molds, a 6,000-year-old process? A US engineer Matti Holtzberg, has spent 30 years trying to send iron and aluminum engines the way of the woolly mammoth. The plastic powerplants he designed and built in the 1980s proved tough enough to race in professional motorsports. But Mr. Holtzberg failed to persuade carmakers that the benefits --- major weight and cost savings -- were worth the risk. So, like the long-lasting battery and the driveway-ready hydrogen fuel cell, plastic engines remain just beyond fruition. What keeps Mr. Holtzberg going is the occasional ally he converts to his way of thinking. Recently he formed a strategic partnership with the Huntsman Corporation of Houston, a global chemical company with 12,000 employees and annual revenues of $10 billion. Huntsman's proven record as an auto industry supplier may bring the clout needed to move plastic engines out of the laboratory and onto the proving grounds where auto engineers are searching for ways to meet the next round of fuel economy targets. Mr. Holtzberg is not the first pioneer to be frustrated in an attempt to move plastics to the mainstream. Henry Ford was an early champion of plastics, commissioning projects to explore alternative materials for car bodies in an era when steel was in short supply because of the military buildup for World War II. And he took the lead in promoting the concept: in 1941, he whacked his personal car with an ax to demonstrate the toughness of an experimental plastic trunk lid. For years Ford cars had been equipped with plastic horn buttons, shift knobs, door handles and timing gears molded from soybean meal. Ford was drawn to plastic for its cost- and weight savings as well as its corrosion resistance. Six years after Henry Ford died, his dream was finally realized. The first of more than 1.5 million Chevrolet Corvettes with fiberglass body panels began rolling off General Motors assembly lines in 1953. Since then, cars have benefited from a steadily rising plastic content. The typical North American-made vehicle now contains over 300 pounds of plastic, according to the Energy Department, making it the second largest material type behind steel. But major powertrain structural components --- engine blocks and cylinder heads, transmission cases and axle housings --- continue to be iron or aluminum castings because of the heat and stress they must endure. Mr. Holtzberg's efforts to change that can be traced at least to 1969. Reading a magazine article at the public library in Hackensack, N.J., he learned of a new plastic said to be tough enough to withstand the harsh conditions inside engines. He obtained a sample, made a piston with it and installed it in the engine of a friend's Austin Mini. The plastic piston lasted 20 minutes Mr. Holtzberg pressed on. During the 1970s, he made and sold plastic pistons -- now with aluminum crowns to withstand combustion temperatures -- and plastic connecting rods for racing engines. In '79, he founded Polimotor (the name is shorthand for polymer motor) to develop plastic-intensive engines. The first Polimotor, a clone of the Ford Pinto 2.3-liter 4-cylinder, used plastic for the block, piston skirts, connecting rods, oil pan and most of the cylinder head. Bore surfaces, piston crowns and combustion-chamber liners were iron or aluminum. The crankshaft and camshaft were standard metal components. Shortly after Mr. Holtzberg's first engine successfully ran, an article in Automotive Industries, a trade magazine, inquired, "What...a Plastic Engine?" Two years later, Popular Science featured a Polimotor on its cover. By then, Mr. Holtzberg had progressed to a second-generation 300-horsepower design weighing 152 pounds; a stock Pinto engine made 88 horsepower and weighed 415 pounds. To prove that his plastic powerplant was durable, Mr. Holtzberg campaigned a Lola racecar in the International Motor Sports Will a plastic car engine help the environment? T "SINCE PLASTIC ENGINE CASTINGS ARE OUTSIDE ANY CAR COMPANY'S MAINSTREAM BUSINESS, ALL THE COST, PROCESSING AND DURABILITY ISSUES WOULD HAVE TO BE RESOLVED IN THE SUPPLY BASE." MINI FEATURE
Media Kit 2010